ANTIGRAFFITI COATING

Protective coating for most surfaces including signs, smooth concrete, metal, wood, and more.

SKU: NGT-3 Categories: ,

Protective coating for most surfaces including signs, smooth concrete, metal, wood, and more.

SOLUTION:
Nano Global Tech (NGT) Anti Graffiti Coating is a clear, thin, protective coating for most surfaces including signs, smooth concrete, metal, wood, and more.
SURFACES NGT Anti Graffiti Coating is perfect for signs including the new diamond reflective highway signs, smooth concrete, metal, wood, plastic and painted surfaces. (Not recommended for use on HDPP or smooth HDPE surfaces.)

COVERAGE:
600-1200 sq. ft./gal (nonporous surfaces)
200 – 400 sq. ft./gal (porous surfaces)
Coverage will vary depending on the porosity and texture of the substrate and application process.

STORAGE & SHELF LIFE:
Avoid excessive temperatures. Use within 2 years of date on container.

SURFACE PREPARATION:
Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material, using NGT Surface Prep.Painted or Coated Surfaces, Plastics and Signs Clean entire surface with NGT Coatings Surface Prep and rinse with fresh water (do not use solvents as this will generally ruin these surfaces).
Make sure the surface is clean and dry, and then apply NGT Anti Graffiti Coating directly over the surface with the spray method only (rolling or brushing our solvent based coating may cause the paint to smear from the pressure of the roller or brush moving across the surface). Unpainted Masonry and Concrete For all porous masonry and concrete make sure the surface is clean and dry. Use NGT Coatings Surface Prep then wash off with water. Once the surface is completely dry, (less than 13% moisture), pre-seal the surface with NGT Quick Seal & Enhance (See NanoTech Coatings Quick Seal & Enhance Data Sheet for complete application instructions) or any good quality water based sealer.
Note: we recommend our Quick Seal & Enhance as it dries in less than 5 minutes which saves on labor and down time. Other sealers can take up to 3 hours to 2 days to dry before application of our Anti Graffiti Coating.
For existing graffiti on unpainted surfaces use NGT Graffiti Remover and rinse with fresh water and allow to dry.

APPLICATION INSTRUCTIONS
Test Area
Due to the wide variety substrates and the various methods of application and environments, always test NGT Anti Graffiti Coating in an inconspicuous location to ensure adhesion and performance. There will be a slight enhancement or change in appearance from the natural surface in addition to a gloss look. (Never roll or brush on painted surfaces or signs. Only spray).

DRY TIME:
Drying Time (@ 77 F, 50% RH):
Drying time is temperate, humidity and film thickness dependent.
Touch: 1 hour / Through: 2-3 hours / Full Cure: 7 Days

CLEAN UP:
Clean tools and equipment with acetone immediately and flush thoroughly after completion of the application. Once product dries in your spray gun, brush or roller it cannot be cleaned by solvents.

CAUTIONS
• Always wear OSHA approved 1910.134 and ANSI Z88 2 respiratory protection. Fresh air and exhaust should be provided in the work area.
If inhaled, move to fresh air. Call physician immediately if physical
difficulties occur.
• Wear butyl-rubber gloves and other skin protection to avoid skin contact. In the event of contact with skin, wash skin thoroughly with soap and water.
• Chemical safety goggles or splash shields are required. Do not wear contacts without eye protection. If you get coating in your eyes rinse with fresh water for 15 minutes and seek immediate medical attention.
• If accidentally swallowed rinse mouth with fresh water for 15 minutes and seek immediate medical attention.
• Ensure excessive ventilation when working in enclosed areas.
HAZMAT INFORMATION:
Coatings Solution UN# 1139, Class 3, Packing Group lll

LIMITED TIME WARRANTY:
NGT guarantees this coating to be defect free and any material that is proven to be defective will be replaced in a like quantity by the manufacture within 10 years of date of purchase. Seller will provide 100% replacement product for product found to be defective for 3 years from the date of purchase, then prorated each of the remaining 7 years under the following terms, Seller must be provided with:
• Proof of purchase receipt.
• Evidence that it has been applied according to the instructions on this container, the data sheet, and instructions and guidelines posted at nanotechcoatings.com.
This warranty is non-transferable. This warranty does not cover wear and tear of the substrate, only the product itself. Any warranty claim must be made in writing and sent to Seller with proof of purchase receipt, supporting materials and Access to the property for inspection and testing as requested by Seller.
Seller will thereafter provide 100% replacement product for product found to be defective for 3 years from date of purchase then prorated each of the remaining years until year 10. This warranty is given in lieu of all other warranties, express or implied, including any warranty of merchantability or fitness for a particular purpose. The remedy stated herein is an exclusive remedy and Seller shall not be responsible for any other damages, including labor or any incidental, consequential, special or punitive damages, whether based on breach of express or implied warranty, negligence, strict liability or other legal theory.